Shop By Vehicle  +

Ford Focus or Escape Steering Column Ignition Housing Flange Switch Genuine New

$ 116.14

This is a special order part. Most special order parts ship out in just a few days. In the rare case of delays, we will keep you informed. 

You can cancel at any time and get a full refund up until the time we ship your package.

Returns and Exchanges

3 Year


Genuine Part

Ships From
Texas, USA

Part Details and Fitment

Steering Column Housing Flange w/ Switch is a Direct Fit For The Following vehicles with Automatic Transmission Only.


Make Model Year Body & Trim Engine & Transmission
Ford Escape 2010 Hybrid, Limited, Limited Hybrid, XLS, XLT 2.5L L4 - Electric/Gas, 2.5L L4 - Gas, 3.0L V6 - Flex
Ford Escape 2009 Hybrid, Limited, Limited Hybrid, XLS, XLT 2.5L L4 - Electric/Gas, 2.5L L4 - Gas, 3.0L V6 - Gas
Ford Escape 2008 Hybrid, Limited, XLS, XLT 2.3L L4 - Electric/Gas, 2.3L L4 - Gas, 3.0L V6 - Gas
Ford Focus 2011 S, SE, SEL, SES 2.0L L4 - Gas
Ford Focus 2010 S, SE, SEL, SES 2.0L L4 - Gas
Ford Focus 2009 S, SE, SEL, SES 2.0L L4 - Gas
Ford Focus 2008 S, SE, SES 2.0L L4 - Gas
Mercury Mariner 2011 Base, Hybrid, Premier 2.5L L4 - Electric/Gas, 2.5L L4 - Gas, 3.0L V6 - Flex
Mercury Mariner 2010 Base, Hybrid, Premier 2.5L L4 - Electric/Gas, 2.5L L4 - Gas, 3.0L V6 - Flex
Mercury Mariner 2009 Base, Hybrid, Premier 2.5L L4 - Electric/Gas, 2.5L L4 - Gas, 3.0L V6 - Gas
Mercury Mariner 2008 Base, Hybrid, Premier 2.3L L4 - Electric/Gas, 2.3L L4 - Gas, 3.0L V6 - Gas

Install Instructions

  1. Disconnect the negative battery terminal.
  2. Remove the steering columns, top and bottom cover and the drivers knee panel under the dash.
  3. Unplug the starter switch on the left side of the column.
  4. Remove the security ring from around the key tumbler by unsnapping it from the housing. Electrical is done.
  5. Three small bolts hold the lock housing onto the turn signal assembly. One bolt is on top, one on the bottom left and one on the right/front. You must use your key to unlock the steering column and turn the wheel to the right to allow access the right/front bolt. Remove all three.
  6. Last, on top of the steering column you will notice an aluminum collar that holds the lock housing assembly in place. On the right side of this collar it is bolted to the steering column by only one anti-theft bolt without a head. (The head of the bolt is gone, designed to break off at the factory when installed for anti-theft reasons so normal tools cannot be used to remove it.) Ours had yellow paint on it. Use a small, very sharp chisel to tap the side of the bolt counter clockwise to loosen it and take it out. DO NOT LOSE IT! You cannot get a replacement.
  7. You should be able to lift up the aluminum collar and remove the old housing assembly.
  8. To use your existing keys you must remove the old tumbles. Put the key into the lock cylinder and turn it one notch only, to the accessory position. On top of the cylinder is a small hole. Put a small torx socket (or nail) in it, push down, pull on the key to remove the tumbler cylinder from the old housing. Put the old tumbler in the new lock housing assembly.
  9. Reverse everything and you are done.

The Original Problem:


After a few years of wear and tear, and climate changes the part to begins to break down structurally.  Heat is one of the main factors of automotive issues. As you may notice, automotive problems seem to be more common in the summer months or in warmer climates.


Our Solution


Our Genuine Part is brand new and has all the latest updates. The part is designed to never fail again. Of course, nothing is perfect, so we back it up with our industry leading warranty in case something does go wrong. This part is made by the same company that made your vehicle, so you know it will be a 100% perfect fit every time, and the quality will be spot on.


Avoid the hassles of aftermarket, and cheap imitation parts. Our Parts just fit right, and just work right every time.




Many of our customers are reporting an install time of around 20 minutes or less. This is really easy to install.  If an installation video is available, you will find it here on this page. We are adding new videos all the time so check back later.


Does it fit my ________???


Our Parts are heavily researched and tested. They only fit what we say they will. Many parts look the same, but in reality, are very different. Please do not purchase if your exact vehicle configuration is not listed, we can promise you it will not fit.

3 Year Warranty

This part is covered y our industry leading 3 Year No Hassle Warranty.


Quality Information

Genuine Part. This part is the exact same part sold at the new car dealership, and includes the same quality and same features for an amazing price.


This part is packaged In Genuine Manufacturers Packaging.

Product Condition

Brand New, Packaging has not been opened.

Production Date:

All parts we sell are factory fresh, are produced less than 1 year ago. Our parts have an average production date of 3 months ago or less.

Hardware and Instructions

This part does not Include hardware or instructions.


Our Customers are reporting an average install time of 20 minutes or less. Install time can vary with individual technical skills.

Part Source

This part is sourced from the USA. (Products are made worldwide, however sourcing from the USA ensures against counterfeits).

Drive With Confidence.

We only sell 100% Genuine Parts. No Chinese Knockoffs, No recalled parts, No Junk!

Learn More About How We Do Auto Parts The Right Way

Customer Reviews

Based on 31 reviews
Ignition housing 2009 Ford Escape
Installation Ease: A little bit of mechanical ability is required
Installation time : 30 Minutes or More
Tools Required: Uncommon, but easily available tools
Part Quality: Excellent Quality
Replacement ignition housing for Mariner
Verified Customer Review
Verified Customer Review
Verified Customer Review